Last week was our final session, we discussed boat transportation, container options, lifting with a crane, launching and retrieving from a ramp and we talked about teak decks over sheet ply
We also talked about Portfolio's, case study approaches and Log Book of Learning
Thanks for your input and interest in Repair and Transportation and Good Luck with the rest of your year in the BAT programme
Thursday, June 30, 2011
Thursday, June 16, 2011
Final Session Tuesday 21st June
Link to Referencing website
Mike's yard, Launching and Hauling
Last week we discussed the visit to Boat Haulage Ltd and the techniques they use to load/unload and Transport boats by road and lift by crane
We also had a discussion on trailers, launching and retrieving on a ramp or beach by trailer. I have placed a power point on the student drive under Marine/Repair and Transportation and there is a link to a helpful (trailer requirements) website on the previous post on this Blog
Remember that transporting a boat is not just to protect what you can see there are items and equipment inside that need to be checked and secure also
Next week the final session will be to go over the course to make sure you are happy with what we have covered, to answer any questions relating to the assessment and to discuss the method to complete several jobs that a repair yard would do regularly
Mike's yard, Launching and Hauling
Last week we discussed the visit to Boat Haulage Ltd and the techniques they use to load/unload and Transport boats by road and lift by crane
We also had a discussion on trailers, launching and retrieving on a ramp or beach by trailer. I have placed a power point on the student drive under Marine/Repair and Transportation and there is a link to a helpful (trailer requirements) website on the previous post on this Blog
Remember that transporting a boat is not just to protect what you can see there are items and equipment inside that need to be checked and secure also
Next week the final session will be to go over the course to make sure you are happy with what we have covered, to answer any questions relating to the assessment and to discuss the method to complete several jobs that a repair yard would do regularly
Thursday, June 9, 2011
Next Week 14 th June
Last week we travelled to Boat Haulage and had an interesting session on moving boats around we were shown a range of trucks that are being used for Transportation of boats ranging in size and up to 100 tons in weight. Pete from Boat Haulage also shared his experience with some ideas on blocking, lifting with a crane, and cradle types.
We then went to the Dry Stack Boat Park at Orams Marine which is another way of storing boats up to 12m long
Next week is the second to last session and we will talk about some of the important aspects of trailer design, this is something you need to prep up on so that you can contribute to that discussion
What do you know about techniques for launching and retrieving on a boat ramp, trailer lights, trailer brakes, Tandem wheels?
http://www.nzta.govt.nz/resources/glovebox-guide-safe-loading-towing/guide-safe-loading-towing.html
We then went to the Dry Stack Boat Park at Orams Marine which is another way of storing boats up to 12m long
Next week is the second to last session and we will talk about some of the important aspects of trailer design, this is something you need to prep up on so that you can contribute to that discussion
What do you know about techniques for launching and retrieving on a boat ramp, trailer lights, trailer brakes, Tandem wheels?
http://www.nzta.govt.nz/resources/glovebox-guide-safe-loading-towing/guide-safe-loading-towing.html
Wednesday, June 1, 2011
next week 7 th June
Hi All,
We are going to travel down to Orams Dry stack to have a look at how that operates, and also visit Boat Haulage Ltd where Bob Wylie operator/manager will share some of his boat transportation experience with us, we will leave from outside the workshop at 1:pm on Tuesday 7th.
You need to do some study on trailerboat trailers.
Preparation of the boat itself for shipping and moving is also a subject we need to discuss
What about containers, what size boat can we get into a container?
We are going to travel down to Orams Dry stack to have a look at how that operates, and also visit Boat Haulage Ltd where Bob Wylie operator/manager will share some of his boat transportation experience with us, we will leave from outside the workshop at 1:pm on Tuesday 7th.
You need to do some study on trailerboat trailers.
Preparation of the boat itself for shipping and moving is also a subject we need to discuss
What about containers, what size boat can we get into a container?
Thursday, May 26, 2011
Next Week 31st May
We will be discussing maintenance issues on metal boats this week, prior to that we will spend some time having a conversation on the workings of a slipway, I will re-visit some of my experience using a slipway of this type and ask you to consider discuss and present your views on the comparisons between this traditional type of slipway and what is now available at such haul-out facilities as Westpark, and Gulf Harbour.
What is the relevance of a slipway today?
looking at both Travelift and slipway facilities what are the advantages and disadvantages?
What is a Grid?
Maintenance on metal boats will be the focus for the second part of the session
http://www.kastenmarine.com/corrosion.htm
We will also discuss lead keels, deck hardware, and aluminium spars and rigging
What is the relevance of a slipway today?
looking at both Travelift and slipway facilities what are the advantages and disadvantages?
What is a Grid?
Maintenance on metal boats will be the focus for the second part of the session
http://www.kastenmarine.com/corrosion.htm
We will also discuss lead keels, deck hardware, and aluminium spars and rigging
Thursday, March 24, 2011
Next Week
Next week 29 March
This section of my repair and Transportation blog I will update each week as we visit yards and participate in discussion
Last week we looked at the affect on timber from a metal tank that was allowed to come into contact with timber, I would like you to think about other types of rot damage, we will discuss this and I would like you all to participate in the discussion
We talked very briefly of grounding all metals exposed to seawater used in boat construction. I would like you to think about that and do some study, we will be participating in discussion on the various methods of protecting metals underwater, both salt and freshwater, is there any difference?
If we are able to get transport we will be visiting Gulf Harbour with a probability of being able to view metal deterioration and protection first hand. We will also look at the travelift operation, different cradle options and view the operation of a repair and maintenance yard first hand
I have booked a Van for lectures 5/4/11, 12/4/11, 3/5/11 and are wait listed next week
Last week we also talked about case studies and the best method to explain the jobs and the order they should be completed in when you do a case study. I have added to the practice case study with some notes to assist to lay out the case studies in a workable format, you should have a look at it with a view to discussing your thoughts and questions on this in class
Those of you that haven't g mailed me how about it guys just another way to keep in contact
Next Week 5th April
We will travel to Westpark and to the TeAtatu Boating club next week. Westpark is a haulout area which is not unlike Gulf Harbour but it is a good place to see a wide range of work being undertaken we can discuss what we see on the spot, we don't have as far to travel and so we should have more time to consider the actual work. Our focus is intended to be to learn about a range of jobs and some approaches we could use to complete a repair or perform maintenance
On the way to Westpark we will stop off at Te Atatu Boating club. This is worth a look there is always interesting work being undertaken. this is more a powerboat location and there are some quite large boats hauled out on the concrete ramp on trailers which aren't roadworthy but are operational within the grounds of the club
We should also take time to catch up on what was important/interesting from the Gulf Harbour Trip I would like to do that in the form of class discussion, give it some thought and be ready to participate.
If you have any interesting pics from that trip it would be great if you sent them to me and they could be put on the Blog
We still haven't finished our discussions on some of the points from last week such as other types of Rot, and the Grounding of metals,
Next Week 12 April
The trip this week was a little bit wet and cold however we did get to view different support structures, more osmosis repair, metal protection underwater.
I did explain a little of the problems that can occur when Gel coat starts to age and the UV damage, along with the knocks that a hull takes after a few years means that its time for resurfacing the hull, a decision at that time has to be made, do we touch up the gel coat and polish the hull or is it time to repaint, I want to have a discussion on this next week, think about a paint system that could be used, it would be helpful to have an idea of the cost of the paint, we could work out a labour cost in class what other costs/problems are incurred when we paint a hull, what is the process
I thought the repair that the boatbuilder was working on was interesting, did you think the method he said he was using to join the planking was OK?
At the Te Atatu boating club hardstand we were able to note the method which was being used to spread the load across the underside of the deck what was that?
It was also interesting to note the differences in the traditional carvel planked boats, there were several older ones with a lot of work to do and then at Westpark several examples that were excellent quality, we need to think about if you owned one of these boats what a maintenance plan might entail
I have would like to explain a method you can use to work out a labour estimate on the practice case study I will show you that next week.
We will spend next week in the theory room catching up on some of these ideas I have put forward
Other types of rot repair
Bonding of metal's for protection (difference between grounding and bonding)http://www.yachtsurvey.com/maitenance.htm
Gel coat repairs, and re paints http://iyp.yachtpaint.com/australia/default.asp
joining the planking on a timber repair
How to work out a labour cost on the practice case study
Next Week 3rd May
Hi All,
I have prepared a schedule for the remaining lectures about Maintaining Repairing and Transporting boats this should give you all an idea on the general subject area we will discuss during each session, the schedule is flexible so that if there is something in particular we need to cover or spend more time on we can do that
This section of my repair and Transportation blog I will update each week as we visit yards and participate in discussion
Last week we looked at the affect on timber from a metal tank that was allowed to come into contact with timber, I would like you to think about other types of rot damage, we will discuss this and I would like you all to participate in the discussion
We talked very briefly of grounding all metals exposed to seawater used in boat construction. I would like you to think about that and do some study, we will be participating in discussion on the various methods of protecting metals underwater, both salt and freshwater, is there any difference?
If we are able to get transport we will be visiting Gulf Harbour with a probability of being able to view metal deterioration and protection first hand. We will also look at the travelift operation, different cradle options and view the operation of a repair and maintenance yard first hand
I have booked a Van for lectures 5/4/11, 12/4/11, 3/5/11 and are wait listed next week
Last week we also talked about case studies and the best method to explain the jobs and the order they should be completed in when you do a case study. I have added to the practice case study with some notes to assist to lay out the case studies in a workable format, you should have a look at it with a view to discussing your thoughts and questions on this in class
Those of you that haven't g mailed me how about it guys just another way to keep in contact
Next Week 5th April
We will travel to Westpark and to the TeAtatu Boating club next week. Westpark is a haulout area which is not unlike Gulf Harbour but it is a good place to see a wide range of work being undertaken we can discuss what we see on the spot, we don't have as far to travel and so we should have more time to consider the actual work. Our focus is intended to be to learn about a range of jobs and some approaches we could use to complete a repair or perform maintenance
On the way to Westpark we will stop off at Te Atatu Boating club. This is worth a look there is always interesting work being undertaken. this is more a powerboat location and there are some quite large boats hauled out on the concrete ramp on trailers which aren't roadworthy but are operational within the grounds of the club
We should also take time to catch up on what was important/interesting from the Gulf Harbour Trip I would like to do that in the form of class discussion, give it some thought and be ready to participate.
If you have any interesting pics from that trip it would be great if you sent them to me and they could be put on the Blog
We still haven't finished our discussions on some of the points from last week such as other types of Rot, and the Grounding of metals,
Next Week 12 April
The trip this week was a little bit wet and cold however we did get to view different support structures, more osmosis repair, metal protection underwater.
I did explain a little of the problems that can occur when Gel coat starts to age and the UV damage, along with the knocks that a hull takes after a few years means that its time for resurfacing the hull, a decision at that time has to be made, do we touch up the gel coat and polish the hull or is it time to repaint, I want to have a discussion on this next week, think about a paint system that could be used, it would be helpful to have an idea of the cost of the paint, we could work out a labour cost in class what other costs/problems are incurred when we paint a hull, what is the process
I thought the repair that the boatbuilder was working on was interesting, did you think the method he said he was using to join the planking was OK?
At the Te Atatu boating club hardstand we were able to note the method which was being used to spread the load across the underside of the deck what was that?
It was also interesting to note the differences in the traditional carvel planked boats, there were several older ones with a lot of work to do and then at Westpark several examples that were excellent quality, we need to think about if you owned one of these boats what a maintenance plan might entail
I have would like to explain a method you can use to work out a labour estimate on the practice case study I will show you that next week.
We will spend next week in the theory room catching up on some of these ideas I have put forward
Other types of rot repair
Bonding of metal's for protection (difference between grounding and bonding)http://www.yachtsurvey.com/maitenance.htm
Gel coat repairs, and re paints http://iyp.yachtpaint.com/australia/default.asp
joining the planking on a timber repair
How to work out a labour cost on the practice case study
Next Week 3rd May
Hi All,
I have prepared a schedule for the remaining lectures about Maintaining Repairing and Transporting boats this should give you all an idea on the general subject area we will discuss during each session, the schedule is flexible so that if there is something in particular we need to cover or spend more time on we can do that
Repair and Transportation
Lecture subjects, (red font not yet covered)
1. Course introduction, class introduction, Assessment description, reading material and websites. Osmosis repair, timber deterioration
2. Osmosis repair, Timber and metal corrosion
3. Field trip Gulf Harbour, Osmosis repair, cradle style, Trave lift operation, hardstand operation, general repair all materials, keel repair
4. Field trip Te Atatu boat club, Westpark, Cradle style, hardstand operation, boat support systems, repair all materials, carvel construction
5. Theory session, cost estimating, painting over Gel coat, metal protection underwater, wood deterioration (dry rot, wet rot, damp timber and metal in contact)
6. FRP maintenance and repair, alteration, a maintenance programme for an FRP boat, Composite repair, retro fitting (composite)
7. Field trip, slipway operation Devonport and Milford
8. Metal construction maintenance and repair, a maintenance programme for a metal boat, protection of metal surfaces, specific jobs for all construction types
8. Metal construction maintenance and repair, a maintenance programme for a metal boat, protection of metal surfaces, specific jobs for all construction types
9. Field Trip, Dry stack operation Oram’s Marine
10. Marine Haulage, Trailers, Boat preparation for moving, crane lifting, cradle moving, ship storage
11. Review all lectures/subjects/assessments
12. Review all lectures
We have completed session 5 and so on the 3rd May we will be covering the information itemised on 6 so do some thinking about work on FRP construction
Something for you to ponder, those of you that have communicated with me by gmail already have seen this suggestion
You must do your own study which is expected to be more than twice the time that you spend at lecture sessions, we have spent 17.5 hours at lectures so far this semester, Have you completed 40 hours of your own study?
I see my role as providing a learning platform for you, therefore I invite you to start your own blog with information that we have discussed so far on field trips or class sessions, I can then see if you are on the right track, maybe you could do a blog or several blogs in groups its a great way of comparing and consolidating your own interpretation of ideas with others.
If you have another group communication you prefer that's fine maybe a google doc
Next week 24th May (two week break)
Hi All,
We are going to go to Devonport yacht club and to Milford cruising club to have a look at how boats are hauled out using a cradle on a slipway, this means that lecture 7 will take place the following week
We can also observe a grid and discuss the purpose and relevance to today's boatbuilding, maintenance, repair
Last Tuesday we didn't finish FRP repair and maintenance and so we will do that probably in week 11
Remember if you decide to do a blog, or a google doc that can also be included in your logbook as a means of study
Something for you to ponder, those of you that have communicated with me by gmail already have seen this suggestion
You must do your own study which is expected to be more than twice the time that you spend at lecture sessions, we have spent 17.5 hours at lectures so far this semester, Have you completed 40 hours of your own study?
I see my role as providing a learning platform for you, therefore I invite you to start your own blog with information that we have discussed so far on field trips or class sessions, I can then see if you are on the right track, maybe you could do a blog or several blogs in groups its a great way of comparing and consolidating your own interpretation of ideas with others.
If you have another group communication you prefer that's fine maybe a google doc
Next week 24th May (two week break)
Hi All,
We are going to go to Devonport yacht club and to Milford cruising club to have a look at how boats are hauled out using a cradle on a slipway, this means that lecture 7 will take place the following week
We can also observe a grid and discuss the purpose and relevance to today's boatbuilding, maintenance, repair
Last Tuesday we didn't finish FRP repair and maintenance and so we will do that probably in week 11
Remember if you decide to do a blog, or a google doc that can also be included in your logbook as a means of study
Thursday, March 10, 2011
galvanic corrosion
Hi All,
I found this a really interesting case of corrosion and its affect on timber. This is a carvel planked hull caulked over double diagonal no glue was used in this type of construction. She is ribbed and has a solid backbone structure with sawn keel floors fastened with through fastenings of bolts and copper nails riveted. What you can see is a copper tank, what would you think has caused the timber deterioration? comment about the construction.
What is the style of cradle that supports the hull? how do you go about a repair of this type? make some notes so that we can discuss it next time
I found this a really interesting case of corrosion and its affect on timber. This is a carvel planked hull caulked over double diagonal no glue was used in this type of construction. She is ribbed and has a solid backbone structure with sawn keel floors fastened with through fastenings of bolts and copper nails riveted. What you can see is a copper tank, what would you think has caused the timber deterioration? comment about the construction.
What is the style of cradle that supports the hull? how do you go about a repair of this type? make some notes so that we can discuss it next time
Wednesday, March 9, 2011
practice case study
Case study
A yacht that has been hauled out and placed in a bilge cradle needs to have its keel resealed
The boat is a 25yr old 12 metre FRP (fibre reinforced plastic) production boat
It has a moderate depth fin keel butted to a stub with single bolts fore and aft and the rest are doubles
The bolts are silicon bronze the singles are ¾ and the doubles are 1”inch there are 10 bolts in total
The keel to stub joint has been broken approximately half way from the forward end
The joint has been attached with a matrix, several layers of chop strand mat and polyester resin.
Describe the procedure to re-seal the keel
Price the repair using a Gaant chart
To find, the labour cost and the total time taken for the job to be completed
List the materials to be charged to the job
A yacht that has been hauled out and placed in a bilge cradle needs to have its keel resealed
The boat is a 25yr old 12 metre FRP (fibre reinforced plastic) production boat
It has a moderate depth fin keel butted to a stub with single bolts fore and aft and the rest are doubles
The bolts are silicon bronze the singles are ¾ and the doubles are 1”inch there are 10 bolts in total
The keel to stub joint has been broken approximately half way from the forward end
The joint has been attached with a matrix, several layers of chop strand mat and polyester resin.
Describe the procedure to re-seal the keel
Price the repair using a Gaant chart
To find, the labour cost and the total time taken for the job to be completed
List the materials to be charged to the job
How do we put a repair plan into place?
List the problems that might need to be considered that could affect the outcome of the job or the efficiency of the job.
Where is the best place to do the work? Do we need it to be undercover? Is it cost effective to move it from where it is?
Do I need a support structure, a cradle, extra lifts on the travelift, or a crane?
What fittings need to be removed? Should they be crack tested in case they need replacing?
Do I have all the tools and equipment I need to do the job? Do I have all the skills or do I have to subcontract.
What is the construction and laminating schedule? Are the materials I require available immediately or do I have to order in.
How long is the job going to take? Make up a time line by listing all the jobs from prep to finishing and put a labour total of hours beside each job.
Work out a cost based on labour, materials, hardstand, and travel lift fees
If we consider these options we could make a description for the case study that was as follows
- The Keel is supported by propping with heavy wooden props or acro proping, two on each side
- Inside the boat keel nuts and washers are removed using a socket and socket wrench
- Care is taken not to damage the exposed bolt threads
- The length is calculated from the top of the bolt head to the lead keel and a hole saw chosen to bore down around the bolts (18mm bolts need at least 4mm clearance)
- Each bolt has a clearance hole made around it by boring down its length to the top of the lead keel with the chosen hole saw
- The hull is separated from the lead keel by lifting with the travelift, the joint may need to be forced apart with the use of steel wedges driven between the lead and the stub
- Once the joint is separated the two equal size blocks are placed between the lead and the stub and the hull rested on the blocks to keep the two surfaces apart. Wash down with fresh water
- Both faces are prepared for re-attaching by using an angle grinder to resurface, and a heat gun to dry
- A stiff epoxy glue mix is prepared and spread over the top of the lead and the stub
- The hull is lowered using the travelift and the keel aligned with the line of the rudder, the line of the mast, using a string line and level. the fore and aft bolts are partially tightened
- The bilge cradle arms are adjusted to support the hull in the correct position and the glue left to dry
- Resin is poured down around each bolt to fill the voids created by the hole saw, this is topped up as it cures
- Keel bolts are re- tightened, filling and fairing completed on the outside
- Undercoat is brushed over the joint area and antifouling applied to the same area and the boat is ready for relaunching
Monday, February 28, 2011
Osmosis Repair
Osmosis avoidance, detection, treatment
Osmosis-Is a problem with fibreglass hulls built from polyester resin... The problem is that water is, able to make its way through the gel coat and in to the fibreglass laminate. Gel coat is not completely waterproof, water penetration does occur. If the water is able to find its way into any air bubbles or small voids that have been left behind from the laminating process it will mix with chemical residue (styrene, MEKP, etc) to form a dense acidic liquid. Because that liquid is more dense than the seawater on the outside of the hull water is drawn from the outside into the void in an effort to equalise the pressure difference, the result is that the void pressurises and forces the outside layer into a blister which shows on the outside of the hull often when the hull is removed from the water a dark liquid can be seen forcing its way back out through the laminate, or gel coat. The blister is actually a small delaminated section of hull, sometimes just under the gel coat but often into the outside layers of CSM depending on the lay up. The process of water penetration is called osmosis and is the same process used in nature by plants to transmit water from roots to leaves.
Avoidance-FRP boats these days are not as prone to osmosis as they were some years ago. Boat builders have realised that they put their product and company name in jeopardy by using cheaper materials and taking shortcuts in production. Hulls that don’t have osmosis problems have a sealed laminate, they use vinyl ester, or isothalic polyester resin rather than orthothalic Quality control the temperature, the humidity, and take good care to lay up using proven techniques. The underwater surface should be sealed with a good thickness of epoxy paint prior to antifouling
Detection- Is not always straight forward, the best way is to view the bottom of the boat when it is first hauled out, and by looking along the wet surface the raised blisters will show up and should be marked. Often as the hull dries the blisters quickly disappear. This is because the surface has been softened and the liquid is allowed to escape as the water is no longer pressuring on the outside of the hull. This will happen quite quickly as the hull dries and often only one hour after haul out the blisters have disappeared. The problem is still there it’s just difficult to individually locate them. Sound tapping with a hammer will find the blisters as they are just small delaminated areas. Often so small that it’s difficult to cover the entire surface with a hammer and feel confident all the blisters have been located. Antifouling should be removed to be sure of finding the full extent of an osmosis problem.
Repair-There are only two proven methods of repair. The first is to remove the affected area of each blister individually, dry out and epoxy fill which is considered as damage control rather than repair. Or the second method is to plane the surface of the hull down to a level where the laminate is healthy (sometimes that is not possible), dry out and re laminate with a resin rich matrix back to original thickness. This is often done with vinyl ester resin and sealed on the outside with a good thickness of epoxy paint.
Osmosis-Is a problem with fibreglass hulls built from polyester resin... The problem is that water is, able to make its way through the gel coat and in to the fibreglass laminate. Gel coat is not completely waterproof, water penetration does occur. If the water is able to find its way into any air bubbles or small voids that have been left behind from the laminating process it will mix with chemical residue (styrene, MEKP, etc) to form a dense acidic liquid. Because that liquid is more dense than the seawater on the outside of the hull water is drawn from the outside into the void in an effort to equalise the pressure difference, the result is that the void pressurises and forces the outside layer into a blister which shows on the outside of the hull often when the hull is removed from the water a dark liquid can be seen forcing its way back out through the laminate, or gel coat. The blister is actually a small delaminated section of hull, sometimes just under the gel coat but often into the outside layers of CSM depending on the lay up. The process of water penetration is called osmosis and is the same process used in nature by plants to transmit water from roots to leaves.
Avoidance-FRP boats these days are not as prone to osmosis as they were some years ago. Boat builders have realised that they put their product and company name in jeopardy by using cheaper materials and taking shortcuts in production. Hulls that don’t have osmosis problems have a sealed laminate, they use vinyl ester, or isothalic polyester resin rather than orthothalic Quality control the temperature, the humidity, and take good care to lay up using proven techniques. The underwater surface should be sealed with a good thickness of epoxy paint prior to antifouling
Detection- Is not always straight forward, the best way is to view the bottom of the boat when it is first hauled out, and by looking along the wet surface the raised blisters will show up and should be marked. Often as the hull dries the blisters quickly disappear. This is because the surface has been softened and the liquid is allowed to escape as the water is no longer pressuring on the outside of the hull. This will happen quite quickly as the hull dries and often only one hour after haul out the blisters have disappeared. The problem is still there it’s just difficult to individually locate them. Sound tapping with a hammer will find the blisters as they are just small delaminated areas. Often so small that it’s difficult to cover the entire surface with a hammer and feel confident all the blisters have been located. Antifouling should be removed to be sure of finding the full extent of an osmosis problem.
Repair-There are only two proven methods of repair. The first is to remove the affected area of each blister individually, dry out and epoxy fill which is considered as damage control rather than repair. Or the second method is to plane the surface of the hull down to a level where the laminate is healthy (sometimes that is not possible), dry out and re laminate with a resin rich matrix back to original thickness. This is often done with vinyl ester resin and sealed on the outside with a good thickness of epoxy paint.
Thursday, February 24, 2011
Case Studies
Case study (covers 5 learning outcomes)
These case studies are to be your Portfolio. They will show that you understand the learning outcomes and you know how to apply them in a practical way
Identify the learning outcome that applies to each case study
Put yourself in the position of managing a boatbuilding maintenance and repair yard when considering the following scenario’s
In your position as manager you need to be able to advise your client on a method of repair from initial survey to job completion. Use sketches as appropriate
Most boat owners are very careful about who they get to repair their ‘pride and joy,’ how much it is going to cost and wether they consider the method of repair is value for money. It is usually the manager’s job to assure them that your yard is the one they should choose to complete the repair
Case 1 (Osmosis Repair)
The Client owns a 12 metre power boat which is a “production built planing hull”. He has been grinding out osmosis blisters individually in the past during each annual haul out, however he thinks that the hull may now need a complete osmosis repair
On hauling out the boat you discover that the hull has many blisters and a complete osmosis repair is required
Describe how you would haul out using the Travel-lift
Describe for the owner your repair method including the method of survey
Case 2 (teak deck repair) (survey)
You have hauled out a yacht, which is built in timber using a cold moulded method; she has a plywood deck over laminated deck beams with teak laid over the plywood, this appears to be in good condition. While replacing deck cabin lights on the underside of the deck you discover extensive areas of soft plywood.
You need to establish what the problem is (survey)
After explaining your survey method describe fully how you could repair the problem
You require knowledge of the typical construction method of a “teak over plywood deck”. It is important to establish the cause of the problem so that it won’t happen again
Case study 3
On the same vessel the owner has complained of leaking windows and wants you to re-seal them. They are glass windows in an anodised aluminium frame. There are two main windows on each side and two smaller windows it is simply a matter of removing the windows and resealing them
Describe the process from start to finish step by step.
Specify the materials used
Case study 4
A 15 metre yacht has been holed above the waterline just behind the main chain plates; there is just the one hole with a small amount of surrounding damage.
The hole size is 900mm long starting from just aft of the chain plate and running aft it is 300mm wide in the middle of the topside
You first need to haul the boat in the travel-lift and place it in a cradle, and then move it inside your factory without the aid of the travel-lift, describe this complete process
The hull is composite, the lay up is as follows inner laminate total thickness is 2.5 mm the core is 12mm and the outside laminate total thickness is 3mm
Describe the repair process step by step including re-surfacing and preparing for re-launching
Case study 5
A client has asked you to Ground the underwater metal fittings on his 15 metre power boat.
Describe what he means
She is a wooden carvel planked hull and he has been having problems with galvanic corrosion
Describe what you would do, what concerns you would have, where you would place the zinc anodes, how you would connect to them
Case Study 6
A Stewart 34 has been booked in to your yard for antifouling, and to have the topsides and coamings polished.
She is one of the more recent polyester production laminate boats and when you have a close look you can see that the Gelcoat is in poor condition. There are a number of dings on the hull where the Gelcoat has been knocked and is damaged to the extent water might penetrate. The deck surface has also had a rough time, having had winch handles and other heavy items dropped on it while the boat has been racing.
You decide that you would be better to advise the owner to paint the hull, decks, and cabin top.
You need to justify your opinion that it will be better value for money to paint the exterior of the boat, even though the cost will be considerably more than just antifouling the bottom and polishing the Gelcoat.
Describe the complete painting process specifying the product you will use
Case study 7
You have to make a decision on the best way to get a 10 metre powerboat to a ship to be delivered to a new owner in Australia.
The options are to truck it to the port and have it loaded from the truck to the ship, or you take the boat by its own power to the ship and have it lifted from the water to the deck of the ship by crane.
Dimensions of the boat as follows:
Length 10m, Beam 3m, displacement 4500 Kilo, height of the hull and cabin top excluding ariels and a cradle 3m
The owner has suggested his preference would be to ship his boat in a container
Analyse the options and describe your analyses
The boat is stored at the Oram’s dry stack, describe how the boat is launched or put on a truck.
http://www.yachtsurvey.com/maitenance.htm
/marinesurvey.com/surveyguide/blisterblues.htm
These case studies are to be your Portfolio. They will show that you understand the learning outcomes and you know how to apply them in a practical way
Identify the learning outcome that applies to each case study
Put yourself in the position of managing a boatbuilding maintenance and repair yard when considering the following scenario’s
In your position as manager you need to be able to advise your client on a method of repair from initial survey to job completion. Use sketches as appropriate
Most boat owners are very careful about who they get to repair their ‘pride and joy,’ how much it is going to cost and wether they consider the method of repair is value for money. It is usually the manager’s job to assure them that your yard is the one they should choose to complete the repair
Case 1 (Osmosis Repair)
The Client owns a 12 metre power boat which is a “production built planing hull”. He has been grinding out osmosis blisters individually in the past during each annual haul out, however he thinks that the hull may now need a complete osmosis repair
On hauling out the boat you discover that the hull has many blisters and a complete osmosis repair is required
Describe how you would haul out using the Travel-lift
Describe for the owner your repair method including the method of survey
Case 2 (teak deck repair) (survey)
You have hauled out a yacht, which is built in timber using a cold moulded method; she has a plywood deck over laminated deck beams with teak laid over the plywood, this appears to be in good condition. While replacing deck cabin lights on the underside of the deck you discover extensive areas of soft plywood.
You need to establish what the problem is (survey)
After explaining your survey method describe fully how you could repair the problem
You require knowledge of the typical construction method of a “teak over plywood deck”. It is important to establish the cause of the problem so that it won’t happen again
Case study 3
On the same vessel the owner has complained of leaking windows and wants you to re-seal them. They are glass windows in an anodised aluminium frame. There are two main windows on each side and two smaller windows it is simply a matter of removing the windows and resealing them
Describe the process from start to finish step by step.
Specify the materials used
Case study 4
A 15 metre yacht has been holed above the waterline just behind the main chain plates; there is just the one hole with a small amount of surrounding damage.
The hole size is 900mm long starting from just aft of the chain plate and running aft it is 300mm wide in the middle of the topside
You first need to haul the boat in the travel-lift and place it in a cradle, and then move it inside your factory without the aid of the travel-lift, describe this complete process
The hull is composite, the lay up is as follows inner laminate total thickness is 2.5 mm the core is 12mm and the outside laminate total thickness is 3mm
Describe the repair process step by step including re-surfacing and preparing for re-launching
Case study 5
A client has asked you to Ground the underwater metal fittings on his 15 metre power boat.
Describe what he means
She is a wooden carvel planked hull and he has been having problems with galvanic corrosion
Describe what you would do, what concerns you would have, where you would place the zinc anodes, how you would connect to them
Case Study 6
A Stewart 34 has been booked in to your yard for antifouling, and to have the topsides and coamings polished.
She is one of the more recent polyester production laminate boats and when you have a close look you can see that the Gelcoat is in poor condition. There are a number of dings on the hull where the Gelcoat has been knocked and is damaged to the extent water might penetrate. The deck surface has also had a rough time, having had winch handles and other heavy items dropped on it while the boat has been racing.
You decide that you would be better to advise the owner to paint the hull, decks, and cabin top.
You need to justify your opinion that it will be better value for money to paint the exterior of the boat, even though the cost will be considerably more than just antifouling the bottom and polishing the Gelcoat.
Describe the complete painting process specifying the product you will use
Case study 7
You have to make a decision on the best way to get a 10 metre powerboat to a ship to be delivered to a new owner in Australia.
The options are to truck it to the port and have it loaded from the truck to the ship, or you take the boat by its own power to the ship and have it lifted from the water to the deck of the ship by crane.
Dimensions of the boat as follows:
Length 10m, Beam 3m, displacement 4500 Kilo, height of the hull and cabin top excluding ariels and a cradle 3m
The owner has suggested his preference would be to ship his boat in a container
Analyse the options and describe your analyses
The boat is stored at the Oram’s dry stack, describe how the boat is launched or put on a truck.
http://www.yachtsurvey.com/maitenance.htm
/marinesurvey.com/surveyguide/blisterblues.htm
Log Book of Learning
Repair and Transportation
Assessment 1
Logbook of learning
This assessment is worth 20% of your final grade
You are required to keep and present to the lecturer a log book of learning that reflects the learning process
Your log book should include examples of marine Repair Maintenance and Transportation which may include sketches with descriptions of the various possibilities.
The logbook will also cover problem solving and critical thinking
The outcomes to be covered by the learning log book are:
1. Assess the maintenance requirements of various vessels.
2. Determine the structural repair status of various vessels.
3. Derive appropriate structural repair requirements for various vessels.
4. Assess a wide range of vessels’ transportation requirements.
5. Investigate various vessels’ storage options.
Due date is 8th July 2011. Hand in to Student Central to be forwarded to
Lecturer Marine Technology Richard Wilson
Email rwilson@unitec.ac.nz
Work Phone 815 4321 ext.8700
Office Location building 107
Assessment 1
Logbook of learning
This assessment is worth 20% of your final grade
You are required to keep and present to the lecturer a log book of learning that reflects the learning process
Your log book should include examples of marine Repair Maintenance and Transportation which may include sketches with descriptions of the various possibilities.
The logbook will also cover problem solving and critical thinking
The outcomes to be covered by the learning log book are:
1. Assess the maintenance requirements of various vessels.
2. Determine the structural repair status of various vessels.
3. Derive appropriate structural repair requirements for various vessels.
4. Assess a wide range of vessels’ transportation requirements.
5. Investigate various vessels’ storage options.
Due date is 8th July 2011. Hand in to Student Central to be forwarded to
Lecturer Marine Technology Richard Wilson
Email rwilson@unitec.ac.nz
Work Phone 815 4321 ext.8700
Office Location building 107
Tuesday, February 22, 2011
portfolio of evidence
testing
Repair and Transportation
Portfolio of evidence
This assessment is worth 80% of your final grade
You are required to produce a portfolio of evidence on detailed analyses of repair maintenance and transportation considerations for a variety of projects covering different vessel types.
A successful portfolio should contain:
An overview introduction to the portfolio
Followed by the case studies 1 to 7
Identifying learning outcomes that fit each case 1 to 5
1. Assess the maintenance requirements of various vessels.
2. Determine the structural repair status of various vessels.
3. Derive appropriate structural repair requirements for various vessels.
4. Assess a wide range of vessels’ transportation requirements.
5. Investigate various vessels’ storage options.
Closing statements
Due date is 8th July 2011 Hand in to Student Central
Lecturer Marine Technology Richard Wilson
Email rwilson@unitec.ac.nz
Work Phone 815 4321 ext.8700
Office Location building 107
Repair and Transportation
Portfolio of evidence
This assessment is worth 80% of your final grade
You are required to produce a portfolio of evidence on detailed analyses of repair maintenance and transportation considerations for a variety of projects covering different vessel types.
A successful portfolio should contain:
An overview introduction to the portfolio
Followed by the case studies 1 to 7
Identifying learning outcomes that fit each case 1 to 5
1. Assess the maintenance requirements of various vessels.
2. Determine the structural repair status of various vessels.
3. Derive appropriate structural repair requirements for various vessels.
4. Assess a wide range of vessels’ transportation requirements.
5. Investigate various vessels’ storage options.
Closing statements
Due date is 8th July 2011 Hand in to Student Central
Lecturer Marine Technology Richard Wilson
Email rwilson@unitec.ac.nz
Work Phone 815 4321 ext.8700
Office Location building 107
Subscribe to:
Posts (Atom)





